Health · 27 calculators
One Rep Max Calculator
A one rep max is the heaviest load you can lift once. Testing it directly is risky, so most lifters estimate it from a lighter set — and the whole topic is really about how much you should trust that estimate.
Last updated
Estimated one rep max (Epley)
116.6667
- The same set under the Brzycki formula
- 112.5
- Load for a 90 per cent working set
- 105
- Reps a 75 per cent load typically supports
- 10
Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.
The formula this calculator uses
Epley: 1RM = w x (1 + reps/30) | Brzycki: 1RM = w x 36 / (37 - reps)
- w
- Weight lifted for the set you completed
- reps
- Repetitions completed with that weight
- 1RM
- Estimated one rep max, a prediction rather than a measurement
- share
- Working percentage of the one rep max, such as 0.9 or 0.75
How to check the result by hand
- 1
Complete a set with clean technique
Choose a weight you can lift for a known number of reps with good form, ideally five or fewer. The whole estimate rests on this set being a genuine effort rather than a comfortable warm-up, so it must be a set you actually finished. If in doubt, use a set on which you could have taken one or two more reps rather than one taken to absolute failure.
- 2
Record the weight and the reps exactly
For 100 kg for five reps, note both numbers precisely. A rounded weight or an uncertain rep count feeds straight into the estimate, and the formulas will happily produce a confident-looking answer from sloppy inputs.
- 3
Apply the Epley formula for the primary estimate
100 x (1 + 5/30) = 116.66667. This is the figure most programming tables assume, and it is the one the calculator reports first.
- 4
Apply the Brzycki formula as a cross-check
100 x 36 / (37 - 5) = 112.5. The two formulas differ by 4.1666667 kg on this set, which tells you the estimate carries a few kilograms of uncertainty and should not be treated as exact.
- 5
Convert the estimate into working loads
Take 90 per cent for a heavy set: 116.66667 x 0.9 = 105. A 75 per cent load typically supports around ten reps, so the single estimate becomes a set of training numbers rather than one figure. Written down, these figures cover a week of sessions without any further arithmetic.
Common Questions
How does the One Rep Max Calculator work?
Both formulas take a set you actually completed and extrapolate to a single maximal lift. For 100 kg for five reps, Epley gives 100 x (1 + 5/30) = 116.6667 and Brzycki gives 100 x 36 / 32 = 112.5. The 4.1667 kg gap is not an arithmetic error — it is the honest uncertainty inside any estimate. Use the figure to set working loads rather than to load a bar you have never tested, because directly testing a one rep max needs a spotter and experience.
What do I need to enter in the One Rep Max Calculator?
It takes 2 inputs: Weight lifted, Repetitions completed. Fields that expect a unit say so next to the label.
Where does Estimated one rep max (Epley) come from?
It comes from 1RM = w x (1 + reps/30) — the simpler of the two forms. The load is multiplied by a factor that grows linearly with the number of repetitions completed.
What is the most common mistake with the One Rep Max Calculator?
Treating the estimate as a measured maximum. A predicted 116.6667 kg does not mean the bar will move. Loading it as though it had been tested invites a failed or dangerous lift; the estimate exists to arrange training loads, not to justify a maximal attempt. The gap between prediction and performance is widest precisely at maximal loads.
For worked examples, common mistakes and the limits of this formula, read the full How To Calculate One Rep Max page.
