CCalclabhub

Everyday Life · 57 calculators

Tile Count Calculator

Tile count is the surface area divided by the area of one tile, with a wastage allowance added and the answer rounded up. The only real decisions are how much wastage to allow and which direction to round.

Last updated

Tiles to order with wastage

146.6667

Room area in square metres
12
Area of one tile in square metres
0.09
Exact tiles without wastage
133.3333

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

The formula this calculator uses

Tiles = (room area / tile area) x (1 + wastage)

A
Area to be covered, in square metres
a
Area of one tile, in the same square unit
w
Wastage rate as a decimal, commonly 0.1 for ten percent
N
Tiles to order, rounded up to a whole number

How to check the result by hand

  1. 1

    Measure the surface in one consistent unit

    Measure the length and width of the floor, or the height and width of the wall, and write both down in the same unit. A room 4 metres by 3 metres gives 4 and 3. If the tape reads in centimetres, convert to metres first, because the tile side will be quoted in metres and the two figures must agree before any division is attempted.

  2. 2

    Multiply to get the area to be covered

    Multiply length by width to get the surface area: 4 x 3 = 12 square metres. If the space is not a simple rectangle, split it into rectangles, compute each one and add the results. Subtract the areas of permanent obstructions such as fitted units or a fixed bath only if they will never be tiled behind.

  3. 3

    Compute the area of a single tile

    Multiply the tile side by itself for a square tile: 0.3 x 0.3 = 0.09 square metres. Rectangular tiles use length times width instead, so a 0.3 by 0.6 metre tile covers 0.18 square metres. Write this figure down separately, because it is the divisor for the next step and the most common place for a unit slip.

  4. 4

    Divide the surface area by the tile area

    Divide the surface area by the area of one tile: 12 / 0.09 = 133.33333333333334. That decimal is the exact number of tiles the geometry demands, with no allowance for cuts or breakage. Keep the full value rather than rounding it here, because rounding too early carries the error into the wastage multiplication that follows.

  5. 5

    Add wastage, then round up to a whole tile

    Multiply the exact count by one plus the wastage rate: 133.33333333333334 x 1.1 = 146.66666666666669 for ten percent. Round that up to 147 tiles, never down, and convert to boxes if the tiles are sold in packs. Order the rounded figure and keep the surplus tiles for future repairs.

Common Questions

How does the Tile Count Calculator work?

Divide the area you must cover by the area of a single tile, then add a wastage margin. A room 4 metres by 3 metres is 12 square metres; a 0.3 metre square tile is 0.09 square metres; and 12 / 0.09 = 133.33333333333334 exact tiles. With ten percent wastage that becomes 133.33333333333334 x 1.1 = 146.66666666666669 tiles, which rounds up to 147 tiles to order. The wastage covers edge cuts, awkward corners and breakages, and the final round is always upward because you cannot buy a fraction of a tile.

What do I need to enter in the Tile Count Calculator?

It takes 4 inputs: Room length, Room width, Tile side, Wastage allowance (percent). Fields that expect a unit say so next to the label.

Where does Tiles to order with wastage come from?

It comes from A = L x W — length times width, with both measurements in one consistent unit. Subtract permanent obstructions only if they will never be tiled behind.

What is the most common mistake with the Tile Count Calculator?

Forgetting the wastage allowance entirely. The exact division gives 133.33333333333334 tiles, and ordering that many ignores every cut and breakage. Add at least ten percent, which here means 146.66666666666669 tiles and a rounded order of 147. A job ordered to the exact area figure almost always runs short near the end, when the offcut tiles are the ones being used.

For worked examples, common mistakes and the limits of this formula, read the full How To Calculate Tile Count page.