Geometry
How To Calculate The Area Of A Rhombus
The area of a rhombus is half the product of its two diagonals, a shortcut that works because those diagonals cross at right angles. This page shows why that formula holds, how the same diagonals give you the side length and perimeter through Pythagoras, and how to apply the numbers in three worked examples.
Last updated
Quick Answer
A = (d1 × d2) / 2
- d1
- The full length of the first diagonal, measured from one corner to the opposite corner
- d2
- The full length of the second diagonal, measured between the other pair of corners
- A
- The area enclosed by the rhombus, in square units
- s
- The length of any one of the four equal sides
Multiply the full length of one diagonal by the full length of the other, then divide by two. With diagonals of 10 and 8 the product is 80 and the area is 40 square units. Halving each diagonal first gives legs of 5 and 4, so the side is the square root of 41, or 6.4031242374328485, and the perimeter is four times that, 25.612496949731394.
What Is The Area Of A Rhombus?
A rhombus is a four-sided figure with all four sides the same length. It belongs to the family of parallelograms, so its opposite sides are parallel and its opposite angles are equal, but the equal-sided condition makes it more specific than a general parallelogram. A square is simply the special case where every angle is a right angle. Because the shape is defined by its side length and one angle, its area cannot be read off from a single measurement the way a square's can, and the diagonals turn out to be the most convenient quantities to work with.
The diagonals of a rhombus cross at their midpoints and meet at right angles. That perpendicular crossing is the whole reason the area formula takes the form it does. Each diagonal splits the shape into two congruent triangles, and the four right-angled triangles around the centre each have legs equal to half of one diagonal and half of the other. Adding the areas of those four triangles gives four times half of half-d1 times half-d2, which simplifies to d1 times d2 divided by two. No trigonometry is needed; the right angles do the work.
There are other valid ways to find the same area. Like any parallelogram, a rhombus has an area equal to its base times its perpendicular height, and if you know a side s and an interior angle theta the area is s squared times the sine of theta. The diagonal formula is preferred when the diagonals are known because it needs no height and no angle, both of which are awkward to measure on a physical rhombus. Each route returns the same number, so you can use whichever pair of measurements you actually have in front of you.
The side length follows from the diagonals by Pythagoras, and this is where the half-diagonals matter. Since the diagonals bisect each other, the four small triangles at the centre are right-angled with legs of d1 over two and d2 over two, and the hypotenuse of each is a side of the rhombus. For diagonals of 10 and 8 the legs are 5 and 4, so the side is the square root of 25 plus 16, which is the square root of 41, or 6.4031242374328485. Confusing the full diagonals with the halves here is the classic source of a badly oversized answer.
Once the side is known the perimeter is immediate: all four sides are equal, so P equals four s. For the worked rhombus that is about 25.612496949731394 units. This makes the perimeter quite different in character from the area, because it depends on the side rather than directly on the diagonals, and it responds to changes in shape in a different way. A rhombus can be sheared while keeping its side length fixed, leaving the perimeter unchanged while the area shrinks toward zero.
The scaling behaviour is worth stating plainly because it is easy to get backwards. Area is linear in each diagonal: double one diagonal while holding the other fixed and the area doubles, because the product doubles. Double both and the area grows fourfold. Contrast this with scaling the side of a similar rhombus, where a factor of two on the side doubles both diagonals and therefore quadruples the area, just as it does for a square. Increasing either diagonal alone always increases the area proportionally, provided the shape remains a valid rhombus.
The two diagonals are not independent of the angles. The longer diagonal joins the two acute corners and the shorter one joins the two obtuse corners, and as the rhombus is squashed flatter the long diagonal lengthens while the short one contracts. Their product still determines the area, so a very flat rhombus can have a large diagonal product but a shape that looks almost like a line only if one diagonal has become tiny. At the two extremes the rhombus closes into a square when the diagonals are equal, and collapses to zero area when either diagonal reaches zero.
Rhombuses appear far beyond the classroom. Floor tiles, diamond shapes on playing cards, the cells of some crystal lattices and the plan form of a kite all reduce to the same geometry, and the diagonal area formula is what lets you estimate material or surface quickly. Surveyors and designers like it because a diagonal is often the easiest span to measure across an awkward quadrilateral. Whenever you can get corner-to-corner distances but not a clean perpendicular height, this formula is the practical route to the enclosed area.
The formula assumes a flat, convex rhombus whose diagonals are measured corner to corner in the same units. It does not directly describe a non-convex dart or a general kite, where only one diagonal is bisected, even though those shapes can look similar. It also says nothing about the volume of a three-dimensional solid built from rhombus faces. Keep the two diagonal measurements in matching units before multiplying, because mixing centimetres and metres produces an area in mixed units that is meaningless until converted.
Formula
A = (d1 × d2) / 2
Formula page →Multiply the full diagonals together and halve the result. The halving accounts for the four right-angled triangles into which the perpendicular diagonals divide the shape, and it is what distinguishes this from the area of a rectangle with the same spans.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| d1 | First full diagonal | length | Corner-to-corner length of one diagonal, not the distance from a corner to the centre. |
| d2 | Second full diagonal | length | Corner-to-corner length of the other diagonal, in the same units as d1. |
| A | Area of the rhombus | square units | Enclosed region, measured in square units of the chosen length unit. |
s = sqrt((d1/2)² + (d2/2)²)
Formula page →Halve each diagonal to get the legs of a right triangle whose hypotenuse is a side of the rhombus, then apply Pythagoras. With diagonals 10 and 8 this gives the square root of 41.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| s | Side length | length | The common length of all four sides, equal to the triangle's hypotenuse. |
| d1/2 | Half of the first diagonal | length | One leg of the central right triangle; halving is essential before squaring. |
| d2/2 | Half of the second diagonal | length | The other leg of the central right triangle. |
P = 4s, with d1 × d2 = 2A
Formula page →The perimeter is four times the side found in the second formula, while the product of the diagonals is exactly twice the area. For the default rhombus the product is 80 and the perimeter is about 25.612496949731394.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| P | Perimeter | length | Total distance around the four equal sides. |
| s | Side length | length | Found from the half-diagonals with Pythagoras before multiplying by four. |
How To Calculate The Area Of A Rhombus
- 1
Measure the two full diagonals
Identify the corner-to-corner distances d1 and d2, not the distances from a corner to the centre where the diagonals cross. In the worked case these are 10 and 8. Check that both are in the same units before doing anything else, since a mixture of centimetres and millimetres will scale the final area incorrectly by a factor of ten or a hundred.
- 2
Multiply the diagonals to get their product
Compute d1 times d2. With 10 and 8 the product is 80. This number is twice the area, so if you accidentally stop here you will be reporting the area of a rectangle that encloses the rhombus four times over. Keeping the product visible makes the next step trivial to audit.
- 3
Halve the product for the area
Divide the product by two: 80 divided by 2 gives an area of 40 square units. The divisor two comes from the right-angled triangles formed by the crossing diagonals, and it applies for every rhombus regardless of its angles. Doubling either diagonal would double the product and therefore double this area.
- 4
Halve each diagonal and apply Pythagoras
For the side length, take half of each diagonal, giving 5 and 4 in the example. These are the legs of a right triangle whose hypotenuse is a side of the rhombus. Square and add them to get 25 plus 16 equal to 41, then take the square root to obtain a side of 6.4031242374328485.
- 5
Multiply the side by four for the perimeter
All four sides are equal, so the perimeter is four times the side just found. Four times 6.4031242374328485 is 25.612496949731394 units. Notice the perimeter carries ordinary length units while the area carries square units, so the two numbers describe different things and should never be compared directly.
Examples
Example 1: The default rhombus: diagonals 10 and 8
- diagonal1
- 10
- diagonal2
- 8
| Step | Calculation | Result |
|---|---|---|
| Full diagonals | d1 = 10, d2 = 8 | 10 and 8 |
| Diagonal product | 10 × 8 | 80 |
| Half-diagonals | 10 ÷ 2 and 8 ÷ 2 | 5 and 4 |
| Side length | sqrt(5² + 4²) | 6.4031242374328485 |
| Perimeter | 4 × 6.4031242374328485 | 25.612496949731394 |
| Area | 80 ÷ 2 | 40 |
Result: With diagonals 10 and 8 the area is 40 square units, the diagonal product is 80, the side is 6.4031242374328485 and the perimeter is 25.612496949731394.
Example 2: A larger rhombus: diagonals 14 and 10
- diagonal1
- 14
- diagonal2
- 10
| Step | Calculation | Result |
|---|---|---|
| Full diagonals | d1 = 14, d2 = 10 | 14 and 10 |
| Diagonal product | 14 × 10 | 140 |
| Half-diagonals | 14 ÷ 2 and 10 ÷ 2 | 7 and 5 |
| Side length | sqrt(7² + 5²) | 8.602325267042627 |
| Perimeter | 4 × 8.602325267042627 | 34.40930106817051 |
| Area | 140 ÷ 2 | 70 |
Result: Diagonals of 14 and 10 give an area of 70 square units, with a diagonal product of 140, a side of 8.602325267042627 and a perimeter of 34.40930106817051.
Example 3: Equal diagonals: a square as a rhombus
- diagonal1
- 10
- diagonal2
- 10
| Step | Calculation | Result |
|---|---|---|
| Full diagonals | d1 = 10, d2 = 10 | 10 and 10 |
| Diagonal product | 10 × 10 | 100 |
| Area | 100 ÷ 2 | 50 |
| Half-diagonals | 10 ÷ 2 and 10 ÷ 2 | 5 and 5 |
| Side length | sqrt(5² + 5²) | 7.0710678118654755 |
| Perimeter | 4 × 7.0710678118654755 | 28.284271247461902 |
Result: A rhombus with both diagonals equal to 10 is a square: its area is 50, its side is 7.0710678118654755 and its perimeter is 28.284271247461902 units.
Calculator
Area
40
- Perimeter
- 25.6125
- Side length
- 6.4031
- Diagonal product
- 80
Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.
Prefer a full-width tool? Open the The Area Of A Rhombus calculator page.
Common Mistakes
Using the half-diagonals in the area formula
The area formula takes the full corner-to-corner diagonals. Substituting the halves, 5 and 4 in the worked case, gives half the correct area because both factors have been divided by two. Reserve the halves for the Pythagoras step that finds the side.
Forgetting to halve the diagonal product
Multiplying the diagonals and reporting 80 as the area confuses the rhombus with a rectangle spanning the same distances. The perpendicular crossing of the diagonals means the enclosed area is exactly half that product, so always divide by two as the final step.
Treating the diagonals as the sides
The diagonals run between opposite corners and are generally longer than a side. Using a diagonal where a side belongs inflates the perimeter badly. Find the side first from the half-diagonals with Pythagoras, then multiply by four.
Assuming the two diagonals are equal
Only a square, the special rhombus with right angles, has equal diagonals. In a general rhombus one is longer and joins the acute corners. Entering the same value twice for both will quietly turn every rhombus into a square and distort the result.
Mixing units between the two diagonals
If one diagonal is measured in centimetres and the other in metres, the product is neither square centimetres nor square metres. Convert both to a common unit before multiplying, and state the resulting area in the corresponding square unit.
Confusing area with perimeter
Area is measured in square units and comes from the diagonal product, while perimeter is a length found from the side. A calculation that reports 25.612496949731394 as an area has actually produced the perimeter of the default rhombus.
FAQ
Why is the area half the product of the diagonals?
Because the diagonals are perpendicular and bisect each other, they cut the rhombus into four right-angled triangles. Each has legs of half one diagonal and half the other, so the four together add up to one half of the full diagonal product.
Does the formula work for a square?
Yes. A square is a rhombus whose angles are all right angles, so its diagonals are equal and perpendicular. Diagonals of 10 and 10 give an area of 50, which matches the familiar side-squared result once you convert the diagonal to a side.
Can I find the area from a side and an angle instead?
Yes. If you know a side s and an interior angle theta, the area is s squared times the sine of theta. That is the general parallelogram formula. Use it when the side and angle are the measurements you actually have rather than the diagonals.
How do I find a missing diagonal if I know the area and the other diagonal?
Rearrange the formula to d1 = 2A divided by d2. For an area of 40 and a second diagonal of 8, the first diagonal is twice 40 over 8, which is 10. This is just the area formula solved for the unknown factor.
Are the diagonals of a rhombus always perpendicular?
Yes, in every rhombus the diagonals meet at right angles and bisect each other. That property is what makes the diagonal area formula possible, and it distinguishes a rhombus from a general parallelogram whose diagonals usually meet at an oblique angle.
What happens to the area if I double one diagonal?
It doubles. Area is proportional to the product of the two diagonals, so scaling one by a factor of two while leaving the other alone scales the area by the same factor. Doubling both diagonals would quadruple the area instead.
References
- [1]Wikipedia, Rhombus — https://en.wikipedia.org/wiki/Rhombus
- [2]Wikipedia, Quadrilateral — https://en.wikipedia.org/wiki/Quadrilateral
- [3]Wikipedia, Pythagorean theorem — https://en.wikipedia.org/wiki/Pythagorean_theorem
